ASME SB-209:2021 pdf download

ASME SB-209:2021 pdf download.Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
1. Scope
1.1 This specification covers aluminum and aluminum- alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 3, and in the following finishes: 1.1.1 Plate in all alloys and sheet in heat-treatable alloys: mill finish. 1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish. N OTE 1—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. N OTE 2—See Specification B632/B632M for tread plate. N OTE 3—See Specification B928/B928M for 5xxx-H116 and 5xxx- H321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in this specification, which do not require the additional corrosion testing/capability called out in ASTM B928/B928M, may be suitable for marine and similar environment applications. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are those ofTable 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 This specification is the inch-pound companion to Specification B209M; therefore, no SI equivalents are pre- sented in the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro- priate safety and health practices and determine the applica- bility ofregulatory limitations prior to use.
4. Ordering Information
4.1 Orders for material to this specification shall include the following information: 4.1.1 This specification designation (which includes the number, the year, and the revision letter, if applicable), 4.1.2 Quantity in pieces or pounds, 4.1.3 Alloy (7.1), 4.1.4 Temper (9.1), 4.1.5 Finish for sheet in nonheat-treatable alloys (Section 1), 4.1.6 For sheet, whether flat or coiled, 4.1.7 Dimensions (thickness, width, and length or coil size), 4.1.8 Tensile property limits and dimensional tolerances for sizes not covered in Table 2 or Table 3 of this specification and in ANSI H35.2, respectively. 4.2 Additionally, orders for material meeting the require- ments of this specification shall include the following infor- mation when required by the purchaser: 4.2.1 Whether a supply ofone ofthe pairs oftempers where shown in Table 2, (H14 or H24) or (H34 or H24), is specifically excluded (Table 2, Footnote C), 4.2.2 Whether heat treatment in accordance with Practice B918 is required (8.2), 4.2.3 Whether bend tests are required (12.1), 4.2.4 Whether testing for stress-corrosion cracking resis- tance of alloy 2124-T851, 2219-T851, or 2219 –T87 is required (13.1), 4.2.5 Whether ultrasonic inspection for aerospace or pres- sure vessels applications is required (Section 17), 4.2.6 Whether inspection or witness of inspection and tests by the purchaser’s representative is required prior to material shipment (18.1),4.2.7 DELETED 4.2.8 Whether there are exceptions to identification marking as provided in B666/B666M (20.1), 4.2.9 Whether Practice B660 applies and, if so, the levels of preservation, packaging, and packing required (21.3), and 4.2.10 For sheet and plate with tensile properties having more than one test direction shown in Table 2 and Table 3, whether tensile testing should be in a direction other than the direction specified in Test Method B557 (Section 9.4).
5. Responsibility for Quality Assurance
5.1 Responsibility for Inspection and Tests—Unless other- wise specified in the contract or purchase order, the producer is responsible for the performance of all inspection and test requirements specified herein. The producer may use their own or any other suitable facilities for the performance of the inspection and test requirements specified herein, unless dis- approved by the purchaser in the order or at the time ofcontract signing. The purchaser shall have the right to perform any of the inspections and tests set forth in this specification where such inspections are deemed necessary to ensure that material conforms to prescribed requirements.