ASME B30.11:2004 pdf download
ASME B30.11:2004 pdf download.Monorails and Underhung Cranes This Standard is one of a series of safety standards on various subjects that have been formulated under the generalauspices ofthe AmericanNational Standards Institute. One purpose of the Standard is to serve as a guide to governmental authorities having jurisdiction over subjects within the scope of the Standard. It is expected, however, that...
ASME B73.2:2016 pdf download
ASME B73.2:2016 pdf download.Specification for Vertical In-Line Centrifugal Pumps for Chemical Process 1 SCOPE This Standard is a design and specification standard that covers metallic centrifugal pumps of vertical shaft single-stage design with suction and discharge nozzles in-line. This Standard includes dimensional inter- changeability requirements and certain design features to facilitate installation and maintenance and enhance reliability and safety of...
ASME B18.8.2:2020 pdf download
ASME B18.8.2:2020 pdf download.Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins (Inch Series) 2 GENERAL DATA FOR PINS 2.1 Types of Pins 2.1.1 TaperPins. Taperpins shall have a uniform taper overthepinlengthwithbothendscrowned.Mostsizesare supplied in both commercial and precision classes, the latter having generally tighter tolerances and being more closely controlled in manufacture. Dimensions for both classes are given...
ASME B73.2:2003 pdf download
ASME B73.2:2003 pdf download.Specification for Vertical In-Line Centrifugal Pumps for Chemical Process 1 SCOPE This Standard covers motor-driven centrifugal pumps of vertical shaft, single stage design with suction and discharge nozzles in line. It includes dimensional inter- changeability requirements and certain design features to facilitate installation and maintenance. It is the intent ofthis Standard thatpumps ofthe samestandarddimen- sion designation, from...
ASME B16.20:2017 pdf download
ASME B16.20:2017 pdf download.SPIRAL-WOUND GASKETS Spiral-wound gaskets shall be constructed as alternate plies (circular layers counted as revolutions) of preformed metal windings and pliant fillers that are spirally wound. Pliant fillers shall not extend below the metal winding on both contact faces of the gasket. Metal winding thick- ness shall be 0.190 mm ± 0.040 mm (0.0075 in. ± 0.0015...
ASME B31EA:2010 pdf download
ASME B31EA:2010 pdf download.Standard for the Seismic Design and Retrofit of Above-Ground Piping Systems 1 PURPOSE This Standard establishes a method for the seismic design of above-ground piping systems in the scope of the ASME B31 Code for Pressure Piping. 1.1 Scope This Standard applies to above-ground, metallic pip- ing systems in the scope of the ASME B31 Code for...
ASME B30.13:2003 pdf download
ASME B30.13:2003 pdf download.STORAGE/RETRIEVAL (S/R)MACHINES AND ASSOCIATED EQUIPMENT Within the general scope defined in Section I, ASME B30.13 applies to storage/retrieval (S/R) machines and associated equipment, such as aisle transfer cars and aisle equipment (as defined in para. 13-0.2.1), and inter- faces with other material handling equipment covered under other standards. The provisions of this Standard applying to S/R machines...
ASME B30.14:2015 pdf download
ASME B30.14:2015 pdf download.Side Boom Tractors Volume B30.14 includes provisions that apply to the construction, installation, operation, inspection, testing, and maintenance of side boom tractors powered by an internal combustion engine used for pipe laying or lift- ing operations, utilizing a lifting boom, drum, wire rope, and/or hydraulic cylinders. The requirements for a side boom tractor that is used for...
ASME B30.19:2000 pdf download
ASME B30.19:2000 pdf download.Cableways fixedcableway: a cablewayconsistingoffixed (nonluffing) towers (masts) that support the track cable(s). The lower and upper load blocks are supported by a carriage pow- ered by inhaul and outhaul ropes to travel on the track cable(s). The functionis to lift, lower, and transportloads a distance between the towers (see Fig. 19-0.2.1-1). luffing cableway: a cableway similar to...
ASME B73.1:2012 pdf download
ASME B73.1:2012 pdf download.Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process 1 SCOPE (a) This Standard is a design and specification stan- dard that covers metallic and solid polymer centrifugal pumps ofhorizontal, end suction single stage, centerline discharge design. This Standard includes dimensional interchangeability requirements and certain design fea- tures to facilitate installation and maintenance and to enhance...