IEC 63067:2020 pdf download

IEC 63067:2020 pdf download.Electrical installations for lighting and beaconing of aerodromes – Connecting devices – General requirements and tests
1 Scope
This document applies to plugs and receptacles for single or multiple pole connecting devices used for aeronautical ground lighting applications. Additional requirements and usage of connecting devices are given in different parts of IEC 61 820 series. Connecting devices complying with this document are suitable for use in environmental class E1 1 according to IEC 61 820-1 .
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60352-2:2006, Solderless connections – Part 2: Crimped connections – General requirements, test methods and practical guidance IEC 60529, Degrees of protection provided by enclosures (IP Code) IEC 61 820-1 , Electrical installations for aeronautical ground lighting at aerodromes – Part 1: Fundamental principles ISO 2859-1 , Sampling procedures for inspection by attributes – Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61 820-1 , and the following apply. NOTE Where the terms “voltage” and “current” are used in this document, they are RMS values, unless otherwise specified. ISO and IEC maintain terminological databases for use in standardization at the following addresses: • IEC Electropedia: available at http://www.electropedia.org/ • ISO Online browsing platform: available at http://www.iso.org/obp 3.1 plug accessory having pin(s) designed to engage with the socket contact(s) of a receptacle, incorporating means for the electrical connection and insulated mechanical casting for retention of cable or wires [SOURCE: IEC 60050-442:1 998, 442-03-01 , modified – “socket-outlet” was replaced by “receptacle”, “mechanical retention” was replaced by “insulated mechanical casting for retention” and “cords” was replaced by “wires”.] 3.2 receptacle accessory having socket contact(s) designed to engage with the pin(s) of a plug, incorporating means for the electrical connection and insulated mechanical casting for retention of cables and wires 3.3 type test conformity test made on one or more items representative of the production 3.4 production test test that is carried out for samples of certain lot according to ISO 2859-1 3.5 class A connecting device accessory that is completed by insulating material moulded around pre-assembled components that are terminated to cable(s) or wire(s) in factory 3.6 class B connecting device accessory consisting of a pre-moulded housing and interface contacts that are meant to be assembled on the field 3.7 primary circuit electric circuit that transfers energy from a power source to the primary winding of an AGL transformer 3.8 secondary circuit electric circuit that transfers energy from the secondary winding of the AGL transformer to a load 3.9 screen continuity conductor copper wire used to make a connection to the screen of a cable for the purpose of continuity or earthing
5 General remarks on tests
5.1 Tests shall be carried out to check compliance with the relevant requirements of this document. Tests are as follows: – type tests shall be made on representative specimens of each type of connecting device; – production tests shall be made according to Annex A. Conditions of 5.2 to 5.5 are applicable to type tests. 5.2 Tests shall be carried out at 23 °C ± 3 °C unless otherwise defined. 5.3 Test shall be performed on six pairs (plugs and receptacles) of samples of each style to demonstrate compliance with the requirements in this document. All tested connecting devices shall pass all the relevant tests of this document. Failure of any one of the connecting devices in any one of the tests shall indicate failure of this product to comply with this specification unless otherwise noted in a particular test. 5.4 Assembled connecting devices of class A, shall be subjected to all the relevant tests of this document. 5.5 Class B connecting devices shall be assembled in accordance with the manufacturer’s instructions to lengths of wire or cable, as appropriate, of at least 0,6 m for all the relevant tests of this document.